ARRIS C250 V2 FPV in all version comes with ARRIS C250 V2 RTF, Skyrc B6AC V2 battery charger, Fatshark Attitude V5 fpv goggle.It is fully assembled, tuned and tested before leaving the factory. C250 V2 is one more professional 250 fpv racing drone produced by ARRIS on the basis of the ARRIS C250. The same as the ARRIS C250, the C250 V2 has the advantage of simple structure and high strength. In the meanwhile, ARRIS C250 V2 adopts 4in1 30A tower for the first time, improve the performance of the drone much.Take it to start your FPV journey.
1. Simple structure frame installed with tower structure ESC/PDB, easy to assemble and easy to repair.
2. High quality 3K Carbon fiber frame, the material is imported from Janpan
3. 4mm thick arms, super strong and durable
4. Super Light frame, only $136g
5. The tower ESC/FC comes with integrated OSD, no need to install it separately
6. The angle of the FPV camera is adjustable
7. 4mm thick arms, super strong and durable
8. High efficiency X2205 2300KV motor provides you better performance and longer working life
9. High quality 5042 3 blade propeller, 10% higher efficiency than normal propellers
10. High safety 4S 1500mah 50C lipo battery
Dimension:195mm x 230mm x 42mm (Propellers not included)
Diagonal Wheelbase: 250mm
Flight Controller: F4 flight Controller
Frame Material: Pure Carbon fiber
Radio System: Radiolink AT9S with R6DSM receiver
Camera: ARRIS FPV Mini Camera
FPV TX: 5.8G 200mw 40CH
Antenna: 5.8G Antenna
Flying Time: 10min hovering
Battery: ARRIS 4S 1500mah 50C Lipo
Charger: Skyrc Imax B6AC V2 Mini Charger
Goggle: Fatshark Attitude V5 OLED FPV Goggle
ARRIS C250 V2 is made of pure carbon fiber material. The upper plate and side plate adopts 1.5mm pure carbon fiber material, decrease the weight of the whole frame. Meanwhile, the motor arm adopts 4mm carbon fiber material, ensure the strength of the frame. The total weight of the frame is about 137g.With the simplify one-piece design and lower gravity center design, all kinds of flight actions can be done with facility.The layout design of the C250 V2 is reasonable, the standard flight controller and PDB board can install there.On the frame, there is reserved space for the XT60 female battery connector.The motor arm has holes for 220x series motors, and both 5 inches and 6 inches propellers can install on the C250 V2 frame.
The main advantages of the 4in1 30A Tower:
1. With the double layer design, you just need to plug the pins between esc and flight controller, flight controller and other electronic components. The layout is more concise, decrease the weight of the drone, provided guarantee for flight performance improvements.
The power for flight controller and camera is provided by the BEC on the flight controller. The power for video transmitter is provided by battery. This improves the anti-interference of the video transmission.
2. The tower integrated the OSD, avoid to install it additionally and the adjustment.The drone could get a quick response to the throttle during the flight.
3. The Tower structure design protects the ESC well during the flight. According to our experience, some of the ESC were damaged by the propeller rotation or tree brunch cut, and some of the ESC were damaged due to the broken of the motor arm during the crash when it installed on top of the motor arm. Sometimes, in order to protect the ESC, we added ESC cover to protect it. From this, the weight of the drone increased. For this tower, the esc integrated in the tower which installed in the middle of the quad frame, the ESCs can be protected quite well and make it looks better.
With the high performance ARRIS X2205 2300KV brushless motor, the ARRIS C250 V2 has outstanding power.
1. Adopts the brand new M5 steel shaft, improving the structure strength.
2. Anti-slip pro design.
3. Upgrade to centrifugal fan design, optimizing the heat dissipation.
4. Adopts original Japan NSK bearing, improving the performance of the motor.
5. Adopts N52 tile-shaped magnets.
6. The motor passed more than 20 kinds of tests before leaving the factory, ensure the quality of the motor.
The ARRIS C250 V2 adopts with the latest 5045 propeller, it has bigger windward area, well balance and strengthen root, and the efficiency is 10% higher than normal propeller. This propeller is the first choice of FPV racing drones.
ARRIS FPV Mini Camera for FPV Racing Drones--ARRIS cat fpv mini camera is specially designed for FPV. This camera performs well in both bright and dark condition with high quality image. And the camera angle on the drone is adjustable.
ARRIS 5.8g 200mW 40-CH video TX and antenna pre-assembled.The ARRIS TS5823L with LED is transmitting a full range of 40 channels and only weighs 10g. It's perfect for a wide range of aircraft!With a goggle or monitor in hand, you can begin your FPV journey.
ARRIS X-Speed C250 V2 has integrated with a remote controller battery warning buzzer, pilot can set the threshold (adjustable) according to CF parameter-adjustment software. In addition, you can also locate your racing drone through triggering the buzzer with the switch D on the transmitter.
Self-level mode is the easiest to fly, because when you leave the stick at the center and not controlling it, your drone just level itself and stays there.This mode is good for beginners.
Manual mode is useful for acrobatics such as flips or rolls, or FPV when smooth and fast control is desired. The picture below is what we set on our own Radiolink AT9 Radio.
Radiolink AT9S 10 Channel 2.4GHz Radio
Frequency: 2.4GHz ISM band (2400MHz to 2483.5MHz)
Modulation mode: QPSK
Channel bandwidth: 5.0 MHz and 250Kbps
Spread spectrum: DSSS&FHSS
Adjacent channel rejection: >38dbm
Transmitter power: less than 100mW (20dbm )
Operating current: 90mA@12V
Operating voltage: 7.4~18.0V
Control distance: More than 900 meters ground, 1500 meters air (the actual controldistance depends on the flying environment)
Channel: 10 channels,5-10 channels are customized
Compatible model: include all 120 degree and 90 degree swash-plate helicopter, all fix wings, glider and multi-rotor
Simulator model: under the simulator model the transmitter action turn off, change to power saving model
Screen: 2.8 inches 16 colorful screen, 240*320 pixels
Support receivers: R9DS(S-BUS&PWM), R10DS and R6DS
Size: AT9S- 183 x 100 x 193mm, R9DS- 41 x 23 x 14mm
High safety ARRIS 4S 1500mah Lipo Battery
ARRIS 4S 1500mAh 50C lipo battery is specially designed for FPV racer. The price of this battery is much higher than the similar batteries in the market, because we only sell top-quality batteries. As we all know, the low quality battery might have potential safety hazard, we will never tolerate such products.For ARRIS 4S 1500mah lipo battery, we have done UN38.3 test,1.2M Drop test,MDS report for it, for the test report, you can check here.
SKYRC IMAX B6AC V2 Professional Balance Charger/Discharger
SKYRC IMAX B6AC V2 is the upgraded version for well-known IMAX B6AC. Compared with B6AC V2, it is more accurate and stable and also has some new features and functions. Users could set the terminal voltage by themselves and connect it to PC for PC control and firmware upgrade. What's more, users could also use it as Lithium Battery Meter and Battery Internal Resistance Meter. There are Automatic Charging Current Limit, Capacity Limit, Temperature Threshold and Processing Time Limit which makes the charger safer than V1.
SKYRC B6AC V2 is a high-performance, micro processor control charge/discharge station with battery management suitable for use with all current battery types, with integral equalizer for six-cell Lithium- Polymer (LiPo), Lithium iron phosphate(LiFe) and Lithium-Ion (LiIon) batteries; maximum 6A charge current and maximum 50W charge power.
AC Input Voltage: 100-240V
DC Input Voltage: 11-18V
Circuit Power: Max Charge: 50W /Max Dischage: 5W
Charge Current Range: 0.1-6.0A
Discharge Current Range: 0.1-2.0A
LiPo/LiFe/LiIon Cells： 1-6S
Pb(Lead Acid) battery Voltage:2-20V
Net Weight: 632g
Dimension: 135 x 144 x 36mm
The Fatshark Attitude V5 headset launches this summer as the feisty little brother to the Dominator HDO. The headset represents a leap forward with the same 30° field of view (FOV) as the Dominator V3, high performance VGA OLED micro-displays and specialty pricing. The limited edition of machine green goggles comes with a digital video recorder (DVR) and a built in modular 5.8GHz OLED dual-receiver diversity making this a comprehensive high-performance package. The included, simple-to-use receiver has one-touch band change capability, channel scanning and a spectrum analyzer for clean and simple channel selection along with internal routing for the second receiver to keep the front of the goggles looking crisp and clean.
--FOV (field of view): 30°
--Interpupillary Distance (IPD): 59 to 69 mm (Adjustable)
--Diopter Lens Slot: Available (lens purchase separately）
Micro Display: Resolution 640 X 400 OLED (NTCS/PAL auto selection)
--analog video recording
--SD card support to 32GB (AVI file)
--Support playback recording file
--Firmware upgrade via SD card
--Auto save recording file when power off
--True Diversity Receivers with OLED display
--(Auto Scan Channel/Spectrum Analyzer)
--DC power port
--AV in/out port
-Color: Black and Green
--Face foam and velcro sticker(easy replacement）
--Anti-fogging mini fan
Attitude V5 OLED Headset
5.8G diversity receiver with OLED display
5.8GHz SpiroNET Circular Polarized antenna
5.8GHz FS RHCP patch antenna
18650 Li-ion Battery Case
Zipper case for carrying
1 x ARRIS C250 V2 Racing Quad Frame
4 x ARRIS X2205 V2 2300KV Brushless Motors
1 x Flycolor Tower w/ F4 30A 4 in 1 ESC + F4 + OSD + PDB
4 x ARRIS 5045 3-blade Propeller
1 x ARRIS FPV camera
1 x 5.8G 200mw 32CH FPV TX
1 x FPV Transmitter Antenna
1 x Radiolink AT9S Transmitter with receiver
1 x ARRIS Buzzer
1 x ARRIS 4S 1500mah Lipo Battery
1 x Skyrc B6AC V2 Professional Balance Charger
1 x Fatshark Attitude V5 OLED FPV Goggle
Note: You will receive two parcels, one with the goggle and one with the rest of the items. Due to the battery in the parcel, the shipping time might be longer than usual.